AIYIMA A07 MAX Amplifier Home Audio 300W X2
AIYIMA A07 MAX Amplifier Home Audio 300W X2
1197 in stock
Brand: Aiyima
Model: TPA3255
Power Output per Channel: 200W and above
Country of Origin: Mainland China
Packaging: Included
Channels: 2 (2.0)
Model Number: AIYIMA A07 MAX
Key Features:
- Stereo Amplifier Mode: 300W + 300W
- Bridgeable Mono Amplifier Mode: 600W
- Upgraded Heat Dissipation
- High-Quality Audio Components in the Amplifier
AIYIMA remains committed to innovation and enhancement, employing top-notch professional audio components with a dedicated focus on HiFi audio.
Our goal is to fulfill your requirements for superior sound quality and versatile product functions. The A07 MAX boasts a unique and innovative design, allowing seamless switching between various usage modes.
This single device offers a multifaceted experience, functioning as a Bridgeable Mono Stereo Amplifier with 600 Watts, a 2-channel amplifier with 300W + 300W output, and a 2.1 stereo amplifier.
Product Description
Chips: TPA3255 + NE5532P
Output Power (2 Channels): 2x300W (@4 Ohm)
Impedance (2 Channels): 4 - 8 Ohm
Output Power (Mono): 2x600W (@2 Ohm)
Speaker Impedance (Mono): 2 - 8 Ohm
3.5mm AUX Maximum Output Level: 1V
Frequency Response: 20Hz ~ 20kHz (±1dB)
Signal-to-Noise Ratio: ≥110dB
Total Harmonic Distortion plus Noise (THD+N): ≤0.007% (@1W)
Input Sensitivity: 1V
Internal Capacitance: 63V
Replaceable Op-Amp Chips: OPA2604AP, OPA2134, MUSEO1/02/03, LME49720NA, LM4562, AD827AQ, etc.
Input Type: RCA Audio Inputs
Working Voltage: DC 24-48V
Power Supply Options: 32V/5A, 36V/6A, 48V/5A
(R+ connects to speaker +, L+ connects to speaker -)
Supported Input Devices: mobile phones, tablets, computers, MP3 players, TVs, etc.
Output Devices: passive speakers, power amplifiers, active speakers
Packaging:
1×A07 MAX Amplifier
1×Power adapter(it's option)
Q: All my cables are connected, but there is no sound output?
A: 1. Check if the machine has started and if the indicator light is on.
2. Is the selection of mono/stereo mode and the connection of the speaker interface correct.
3. If the above two points are normal, check whether the playback device of the input sound
source is paused, muted, or the volume is at the minimum.
Q: Why is the sound distorted?
A: The input level may be too large. If the volume of the sound source equipment is adjusted
to the maximum, and the volume of the machine is also adjusted to the maximum, it is
easy to be distorted. At this time, turn down the volume of the sound source input device
or machine.
Q: Why does the volume of the machine remain the same, but the sound level
is different when connecting to different audio sources (for example,
connect a CD first, then a mobile phone)?
A: The amplitude of electrical signals output by different playback devices is different. For
example, mobile phones are usually 0.35V, while CDs are 1V. The natural sound size is
different.
Q: Why does the horn emit a loud electrical current sound or buzzing sound?
A: 1. If you are not using the original standard power supply, please replace the power supply
and test again. Many power supplies in the market have interference, which will cause
current sound.
2. When the signal line without shielding is used, there will be interference signals entering
the power amplifier for amplification. It is recommended that you replace the signal line
with shielding.
3. There is still noise after troubleshooting the above two points, Please confirm the noise
is from the external or the internal. Disconnect all inputs, only retain the power supply
and output cable, if the noise disappears, that means the noise is from the audio input.
If the noise is still there, the noise may be caused by interference with the power supply
or generated inside the amplifier
Q: Why there is no sound or very little sound after the amplifier is connected
to the speaker?
A: 1. Please check the audio source has been turned on and the volume is not at the minimum.
2. Please confirm whether the speaker and amplifier match ( For example, the speaker is
fixed resistance or fixed voltage, the power of speaker is too much over the power of the
amplifier etc.).
Q: What are the reasons for the unbalanced left and right volume of the s
speakers and how to eliminate them?
A: Please check audio source, input cable, volume potentiometer (some amplifiers have
balanced control or separate volume control of left and right channel ), speaker cable,
speakers (whether the position and the distance is symmetrical) and other factors.
Q: Why is there a thumping sound when switching on/off?
A: Please confirm the on-off sequence is correct, normally it follows the order of signal
transmission when turn on: audio source → preamp / DAC → amplifier → speaker. (The
sequence is reversed when switching off. As the internal capacitors will be discharged for a
while after shutdown. If turn off the preamp firstly and then turn off amplifier, impact
sound will be easily caused which may damage the amplifier or speaker in severe cases).